Horizontal CNC Lathes
Seventeen flat-bed machines in three builds: standard horizontals for chuck and shaft work, heavy frames that take 1250–2500 mm swing and 2–20 m between centres, and gang-tool lathes for small precision parts.
01 / 11 models
Horizontal CNC lathes
Flat-bed machines with hardened and ground ways, from a 500 mm chuck job up to 2 m swing. Large spindle bores for bar and tube work.
-
CAK6150D Horizontal CNC lathe -
CFK6163B Horizontal CNC lathe -
CFK6180Q Horizontal CNC lathe -
CFK6180B Horizontal CNC lathe -
CFK6180D Horizontal CNC lathe -
CK6185B Horizontal CNC lathe -
CFK61100Q-CFK61100D Horizontal CNC lathe -
CAK61100B-CAK61125B Horizontal CNC lathe -
CAK61100B-CAK61125B-CAK61140B-CAK61160B Horizontal CNC lathe -
CK61160C-CK61180C-CK61200C Horizontal CNC lathe -
HT65 Horizontal CNC lathe
02 / 3 models
Gang-tool CNC lathes
φ240 swing, φ57 spindle bore and 6000 rpm, with spindle run-out under 2 µm. For instrument, medical and electronic parts.
03 / 3 models
Heavy horizontal CNC lathes
1250-2500 mm swing over the bed and 2-20 m between centres, with the main drive separated from the feed drive.
Choosing A Lathe
Bed Type Follows The Part
Sixty models is a lot to read through. Send the part instead: the largest diameter, the length, the material and the tolerance, and we will name the two or three that fit and say why.
-
Flat bed for weight
A wide flat bed carries heavy, long work and damps the cut. It is the right choice for shafts, rolls and anything needing a steady rest, and it is easier to load with a crane.
-
Slant bed for chips and speed
Chips fall into the conveyor instead of piling on the ways, and the turret sits closer to the spindle centreline. Best for repeat production of medium parts.
-
Vertical for diameter
Once the part is heavier than it is long, gravity works with you rather than against you. Flanges, rings, wheels and gearbox cases belong on a table, not between centres.
-
Y-axis when it saves a setup
A power turret and a C-axis pay for themselves the moment the part would otherwise move to a machining centre for a keyway, a flat or a cross hole.
Every model page carries the specification we hold on file. Foundation drawings and ISO 230-2 acceptance figures come with the quotation.
Request A Specification SheetBuying FAQs
Horizontal CNC Lathes Questions, Answered
What is the practical turning limit on these flat-bed CNC lathes?
The group runs from a 500 mm chuck job up to 2 m swing on the standard frames, with the heavy series carrying 1250–2500 mm swing and 2–20 m between centres. Remember the working figure is maximum turning diameter over the cross slide, not swing over bed — on the HT65 those are 650 mm against 890 mm.
Can these machines handle bar and tube work through the spindle?
Yes — large spindle bores are a design point of the group. The HT65 carries a Φ106 mm main bore, and the gang-tool machines feed small precision parts from bar. For pipe with couplings already fitted, step up to the pipe threading lathes with their oversized through-bores instead.
When do I need a steady rest, and are they available here?
Once the unsupported length runs past roughly ten diameters, deflection starts to show in the finish, and a steady becomes cheaper than scrap. Steady rests for long shaft work are catalogued across the group — quote the finished length and smallest diameter and the right frames get quoted with the machine.
What keeps the ways accurate on a hard-worked flat-bed lathe?
The beds are cast in one piece in resin sand, aged before machining, and the way faces are hardened by ultrasonic-frequency quenching, with saddle faces lined in Turcite. That combination is what lets a flat bed take interrupted cuts year after year without the geometry walking.